東菱產品中心
-
耐磨試驗機
-
線材伸長率試驗機
- 插拔力試驗機
- 拉力試驗機
- 振動試驗機
- 跌落試驗機
-
頭戴式耳機試驗機
-
彎折試驗機
-
線材彎折試驗機
-
手機/電腦/電子產品檢測設...
-
環境試驗設備
-
電線電纜檢測設備
-
紙品包裝檢測設備
- 手機電腦檢測設備
-
箱包手袋檢測設備
-
紡織服裝檢測設備
- 橡膠塑料檢測設備
-
家私玩具檢測設備
-
油漆涂料檢測設備
-
插頭插座檢測設備
產品詳情
簡單介紹：
本電源線彎曲試驗機專門試驗插頭引出線及電線之耐折強度。試法是將試樣固定在夾具上，并加一定荷重，試驗時夾具左右擺動，經一定次數后檢視其斷線率，或至全部斷線無法通電時查看其總計擺動次數。本機能自動計數，試樣彎折至斷線無法通電時，并能自動停止操作。
詳情介紹：
UL817、CSA22.2、IEC884-1、CCC、GB2099.1、VDE、SAA
本電源線彎曲試驗機專門試驗插頭引出線及電線之耐折強度。試法是將試樣固定在夾具上，并加一定荷重，試驗時夾具左右擺動，經一定次數后檢視其斷線率，或至全部斷線無法通電時查看其總計擺動次數。本機能自動計數，試樣彎折至斷線無法通電時，并能自動停止操作。
This tester is specialized in testing the flexing endurance between power cord and blades，and is capable of testing the flexibility resistance of the cord itself。Samples are to be secured in the jaws of the flexing apparatus，and cord is to hang vertically with the weight tied on the lower end of it。The rotating jaws are to be adjusted to rotate to the angle of 90 degree to each side of the centered position。After a certain cycles is reached or until specimen is broken，detect the breakage ratio or calcuate the total cycles。This machine is able to auto-count and auto-stop during specimen broken。
本電源線彎曲試驗機專門試驗插頭引出線及電線之耐折強度。試法是將試樣固定在夾具上，并加一定荷重，試驗時夾具左右擺動，經一定次數后檢視其斷線率，或至全部斷線無法通電時查看其總計擺動次數。本機能自動計數，試樣彎折至斷線無法通電時，并能自動停止操作。
This tester is specialized in testing the flexing endurance between power cord and blades，and is capable of testing the flexibility resistance of the cord itself。Samples are to be secured in the jaws of the flexing apparatus，and cord is to hang vertically with the weight tied on the lower end of it。The rotating jaws are to be adjusted to rotate to the angle of 90 degree to each side of the centered position。After a certain cycles is reached or until specimen is broken，detect the breakage ratio or calcuate the total cycles。This machine is able to auto-count and auto-stop during specimen broken。
試料數量 Specimen Volume | 6 組 (sets) |
擺動角度 Flexing angles | 左右各 45°、60°、90° 可調 |
擺動速度 Flexing speed | 0 ~ 60 次/分鐘，可調節變頻器控制，數字顯示 |
自動計數器 Auto - counter | 6 組 6 位數，分別計數，數字顯示 |
荷重 Load | 113g、284g、10N、20N 各 6 個或訂制 |
電源 Power | AC220V / 50Hz |